Highline TV Articles

LatestBlog

How to scan for channels with your OTA antenna

How to scan for channels with your OTA antenna

When you cut the cord and purchase a new antenna, you get an amazing feeling. However, you will have to do some initial configurations on your side, before you can go ahead and enjoy content on it. That’s where you need to think about scanning for the channels. Our tool below will let you know about how many Local TV channels you’ll get.


Find available local channels




When you are scanning the channels, you locate the channels that are broadcaster over different frequencies. Then their frequencies are stored in your television, against the channel numbers. Therefore, you don’t need to go through this hassle again on the next time. You just need to enter the channel number and you will be able to see content broadcasted on your television.

How to scan for channels?

In order to scan for the channels, you will need to access the Menu of your television. You will be able to do this with the remote controller. Since the televisions are different from one to another, you will have to go through the user manual and figure out how to access the menu of your television with your remote controller.

Here are the steps that you will have to follow when you are scanning for channels in a typical television. If you need more information please refer to our Starter Guide

Related Post: How to cancel HBO Now

Setting up the HighLine TV Antenna

Before you begin, you will need to set up the HighLine TV antenna. You need to connect the coaxial cable to the television and make sure that everything is in working condition for you to go ahead. It is also important to make sure that you have positioned your television in a place, where there is a good signal reception.

Antenna Installation
Installing you Antenna is as easy as 1,2,3

Access Menu from your television

As the next step, you will need to access Menu from your television. As mentioned earlier, you will need to figure out how to access the menu on your television by going through the user manual. But it is an easy thing to do and you will also be able to figure out by just taking a look at your remote controlled. Usually, you will be able to see a button in the remote controller called menu.

Locate settings or a similar item in the menu

Once you get to the menu, you should locate settings in the screen, or something similar to it. Then you will have to navigate to it. After that, you must select the menu. It is perfectly fine to do a trial and error approach and figure out the functionality of available icons in your screen.

Locate channel setup or a similar menu

Now you need to locate channel setup or any other similar menu, which gives the similar meaning. This can even be indicated as channels in some of the television. Again, you can do a trial and error approach and locate the channel setup. When you get that correct, you will be able to proceed to the next step.

Scan for channels

Once you get into channel setup, you will be able to see the option, which you can use to scan the channels. Usually, there are two different modes available for you to scan the channels. The first method is to do an automatic scan and the second method is to do a manual scan. An automatic scan would be the most appropriate way to go forward, as it can help you to locate the channels with minimum effort.

During the scanning process, you will be able to see how your television locates the channels and stores them in your television. You need to allow your television to do this and all the channels will be scanned and stored within a short period of time. Related Post: HOW TO CANCEL AMAZON PRIME.

Troubleshoot

If the process goes well, you will be able to navigate to the channel numbers and see how different channels have been stored in it. But if you don’t see it, you are encouraged to follow the step 4 and step 5 again. Then you will be able to get the job done. Placement of the antenna will effect the amount of channels that you get.

Antenna Placement

You should also keep in mind that scanning for channels multiple times can provide you with different numbers each of the time. If you are still having issues, you can reposition your antenna. Then you will be able to see changes in the channel scanning. This will help you to get the channel scanning job done, without facing any difficulties.

See what local channels you can get!

click above to see what channels you’ll get in your area

Frequently Asked Questions




Get FREE TV Today

Leave a Reply

Your email address will not be published. Required fields are marked *

FREE DELIVERY on all orders
100% Money back satisfaction guarantee
CUT THE CORD on cable and save $$$
24/7 Customer Support Available
Navigation